December 14, 2013

DIY-1 Construction Instructions!

After a long wait, I finally have all the pictures necessary for you to create your own DIY-1 air blaster! This is what you can expect to build out of my DIY blaster kits, without the need of any power tools. At most, you'll need a hammer to assemble some pieces after applying PVC cement, and either wrenches or pliers for twisting and bending parts as needed.

This is my testing model. It's lovely :) But slightly different from the final model.

Complete instructions will be available after the jump!

You will need:
  • PVC primer and cement
  • Teflon tape
  • Silicone grease
  • Goop or similar high-strength adhesive
  • Any kind of handheld saw
  • A few pliers or wrenches
Parts list:
  • Lengths of 1/2", 3/4" Sch. 40 PVC pipe
  • 1/2" CPVC CTS tubing
  • 1" and 3/4" PVC Tees
  • 1" x 1/2" PVC bushing (spig. x socket)
  • 1" x 3/4" PVC bushing (spig. x socket)
  • 1" x 3/4" PVC bushing (spigot x female)
  • 3/4" male x 1/2" socket PVC adapter
  • 3/4" x 1/2" PVC bushing (spig. x female)
  • 1/2" x 1/4" Galvanized Steel bushing
  • 1/4" male NPT miniature pressure relief valve (made for or set at 30 psi)
  • Bell Airstrike 300 Dual Action Bike Frame Pump (or 3/4" PVC homemade pump, if you feel adventurous)
  • 5/8" x 13/16" rubber o-ring
  • 1/2" copper tubing coupler
  • 3/8 trade size flat faucet washer (5/8" OD)
  • 1/2 trade size beveled faucet washer (3/4" OD)
  • 3/16" rod/tubing, steel or aluminum
  • 3/16" Push nut washer
  • #12 steel flat washers
  • small spring
Procedural Notes:
  • For all PVC slip joints, use primer, then cement to properly seal.
  • For all threaded connections, wrap the male thread with a strip of teflon tape, then twist to assemble an airtight seal. Tighten until turning the parts takes extra effort - tightening too much will break the plastic pieces.

Lower Tank Assembly - Pump and Pressure Relief Valve

Take your 3/4" tee. Twist the 3/4" x 1/2" bushing and the galvanized steel bushing together, and solvent weld into one of the sides. Connect a short length of 3/4" PVC with the top of the tee. Remove the black tip from your pump, and slide it into the remaining arm. It should make a tight fit. Goop in place and let the adhesive cure at least 12 hours (a day is preferable).

Upper Tank Assembly - Pull Valve and Stock Attachment Point

For the front of your tank, put the 1/2" PVC stub and 1" x 1/2" slip bushing together. Then, place your o-ring inside the bushing, behind the pipe. It will be a tight fit, but it will go flat with a little convincing. Place in one of your tee's main arms.


Put your 1" x 3/4" bushing in the side arm of your tee. Finally, put the 1" by 3/4" threaded bushing in the last socket.

Now for the back of your tank! Hammer some 1/2" CPVC into 1/2" PVC, like you would for a dart barrel. Slide the 3/4" male x 1/2" socket over the CPVC as shown.



Cut down your CPVC so it will only extend partway into your air tank. Then, slide on your copper tubing coupling - it may take some force, since they typically have a small metal stop in the middle. But don't do it ALL the way. Leave space at the end for gooping in your 5/8" OD flat faucet washer.



Twist this piece into place, to confirm that you did it correctly. You should be able to remove the pin and all for any maintenance issues that may arise over the life of the blaster - greasing the rubber surfaces, replacing a damaged seal, etc.

Firing Valve Assembly

Constructing the valve is relatively easy. 3/16" rod or tubing slides perfectly within faucet washers, and with a little silicone grease makes for an airtight seal. The parts from my test model are pictured.

Put your spring between two metal washers. This will help prevent the thin spring wire from deforming the rubber washers when under compression. Make sure the beveled side of the 3/4" OD washer faces the o-ring at the barrel end. Finally, the push nut washer is designed to NOT be removed. Make sure to test your valve's seal before finally capping the rod - there's enough friction to keep the washers in place for a test pull. Note that your spring should return the valve pin to its resting position when you release it. If it does not do this, you'll need to either fill the gap (use a longer piece of CPVC, add spacers to the valve pin, etc) or get a longer spring (or two springs side by side). Once that's taken care of, put everything together and cap the valve pin.

At this point, all that's left is the trigger and stock. Pictured is my test model - due to its construction, it had no place to add a stock and trigger, unlike the current design. However, the concept is still the same! Your 1/2" PVC stock will need a slot cut lengthwise into it. Using a few pliers or monkey wrenches, bend the end of your pin into a 90° curve. Slide the PVC over it and into place. After that, it's up to you how to orient the trigger and where to place any grip you might want. It's simple enough to use a 1/2" PVC tee and more pipe for your grip. I've actually come to like putting the handle/pin to the side that my pump hand is on, and gripping the tank itself.

Now you have a complete DIY air blaster! At capacity (requiring only a few pumps), darts easily go 100'+ out of singled barrels, and hit in the 90'-100' range when used with a PVC wye hopper.

If you want to support the effort to make DIY blaster kits, please take a look HERE and feel free to contribute to the campaign! :D

54 comments:

  1. Hi
    I have the huntsman 50 and I have disassembled it
    but now I do not know how assembly it
    you can help me ?

    ReplyDelete
  2. I think it looks amazing. I'm not sure I would have had the patience that you had though!

    ReplyDelete
  3. I think your main item for your creation is pvc pipes

    ReplyDelete
  4. Loved you post! I have been forever confused about choosing some good quality pvc hoses and your post is a great help. It is quite comprehensive and now I am able to decide which one to choose. Thanks a ton!

    ReplyDelete
  5. The ILO General Conference made plans to work towards the end of all future asbestos use to secure the wellbeing of specialists. mike

    ReplyDelete
  6. If you're hoping for a heavy duty construction rain suit that also has some breathability to it, look no further than this impressive set from Grundens.cordless screwdriver

    ReplyDelete
  7. Hi I was searching for the blogs for many times, now I have reached at the right place. hero tower hyderabad

    ReplyDelete
  8. superb way of explaining, and great blog to get wonderful information.
    construction company

    ReplyDelete
  9. I’m trampled by your contents carry on the wonderful work.
    food court

    ReplyDelete
  10. Construction managers are versatile workers, encompassing the job for an architect, statistician, designer and draftsman, an engineer, or a foreman.roofing company Minneapolis

    ReplyDelete
  11. PR is tied in with creating introduction and by conversing with an industry experienced PR organization construction firms ought to have the capacity to captivate everyone and get more deals enquiries. tower crane signage

    ReplyDelete
  12. Once you are through with all this you need to select a proper constructor. Before choosing a contractor you will need to get a building permit from the government.construction equipment dealers

    ReplyDelete
  13. Good. Explained beautifully the usage of PVC piping work here. Similarly as per Civil Engineering standards, IS procedures, methods and more updated information, images and videos visit https://myhomemydesign.in/plumbing/

    ReplyDelete
  14. I have read all the comments and suggestions posted by the visitors for this article are very fine,We will wait for your next article so only.Thanks! Electrical Services Sarasota

    ReplyDelete
  15. Thanks meant for sharing this type of satisfying opinion, written piece is fastidious, that’s why I’ve read it completely.
    hyderabad mall list

    ReplyDelete
  16. The common materials used are timber, stone and brick. The cost of construction is on a "per square foot" basis. This is since homes can vary significantly on local site considerations, conditions, and economies of scale.flat roof repair Toronto

    ReplyDelete
  17. If somebody wants expert take on the main topic of blogging next I advise him/her to go to this site, continue the fussy job.
    telephone numbers

    ReplyDelete
  18. If somebody wants expert take on the main topic of blogging next I advise him/her to go to this site, continue the fussy job.
    pakistani movies songs

    ReplyDelete
  19. This written piece gives fastidious understanding yet.
    IP camera systems

    ReplyDelete
  20. I see the greatest contents on your blog and I extremely love reading them.
    self storage camera system

    ReplyDelete
  21. Thanks for compiling such nicest information in your blogs. Articles are very informative and hope again I’ll find more like that.
    camera poles

    ReplyDelete
  22. I went over this website and I conceive you've got a large number of splendid information,
    self storage security cameras

    ReplyDelete
  23. It’s really such nice information to get advantage from.
    car wash camera systems

    ReplyDelete
  24. This written piece gives fastidious understanding yet.
    www.telephonecodes.org

    ReplyDelete
  25. This written piece gives fastidious understanding yet.
    telephone

    ReplyDelete
  26. Fascinating information I haven’t been experienced such information in quite a long time.
    telephonecodes

    ReplyDelete
  27. Nobody can reject the info you have given in the blogs, this is actually a great work.
    telephonecodes.org

    ReplyDelete
  28. These are actually wonderful some ideas in the blog. You have touched good quality points here. In whatever way continue writing.
    Pay Per Click

    ReplyDelete
  29. You have really selected the suitable topic; this is one of my favorite blogs.
    Scott Lanzon Knoxville

    ReplyDelete
  30. Fascinating information I haven’t been experienced such information in quite a long time.
    Scott Lanzon Knoxville

    ReplyDelete
  31. These are actually wonderful some ideas in the blog. You have touched good quality points here. In whatever way continue writing.
    crp plastics

    ReplyDelete
  32. I feel happiness to read the content that you are posting.
    recycled plastic adirondack chairs

    ReplyDelete
  33. No wonder why you receive countless of feedbacks.
    crp plastics

    ReplyDelete
  34. I truly get pleasure from while I read your blogs and its content.
    http://www.telephonecodes.org

    ReplyDelete
  35. This blog Info is fabulous; I must wanna see best more from your writers.
    www.telephonecodes.org

    ReplyDelete
  36. These are actually wonderful some ideas in the blog. You have touched good quality points here. In whatever way continue writing.
    Scott Lanzon Knoxville

    ReplyDelete
  37. It’s amazing in support of me to truly have a blog site, which will be valuable meant for my knowledge. Thanks admin.
    WEIGHT LOSSTHERAPY

    ReplyDelete
  38. Superb way of explaining, and great blog to get wonderful information.
    dgtoothpaste.com

    ReplyDelete
  39. This short article posted only at the web site is truly good.
    ONLINE SLOTS

    ReplyDelete
  40. I went over this website and I conceive you've got a large number of splendid information,
    Bingo Games

    ReplyDelete
  41. You have touched good quality points here. In whatever way continue writing.
    20 yard dumpster company new york

    ReplyDelete
  42. If somebody wants expert take on the main topic of blogging next I advise him/her to go to this site, continue the fussy job. his comment is here

    ReplyDelete
  43. نعمل على مكافحة الحشرات في الدمام لحماية المكان من جميع أنواع الزواحف ، خاصة في الحدائق الخلفية والأمامية للمنازل أو على الأسطح ومع التخلص من الحشرات في الدمام ستعمل على التخلص منها على الفور والعمل على ما يلي: -

    شركة مكافحة النمل الابيض بالرياض
    شركة مكافحة حشرات بالرياض
    شركة رش مبيدات بالرياض
    افضل شركة مكافحة حشرات

    ReplyDelete
  44. I’m impressed with the special and informative contents that you just offer in such short timing. learn this here now

    ReplyDelete
  45. Hi Dear, have you been certainly visiting this site daily, if that's the case you then will certainly get good knowledge. my site

    ReplyDelete
  46. Thanks meant for sharing this type of satisfying opinion, written piece is fastidious, that’s why I’ve read it completely.

    top 5 home security systems

    ReplyDelete
  47. I know this is quality based blogs along with other stuff.
    Select My Shaver

    ReplyDelete
  48. Quickly this site will indisputably be famous among all blogging people, because of its fastidious articles or reviews.
    containerrentalnewyork

    ReplyDelete
  49. This is one of the most important blogs that I have seen, keep it up!
    rentdumpsternewyork

    ReplyDelete
  50. I have checked this link this is really important for the people to get benefit from.
    constructiondumpsternewyork

    ReplyDelete
  51. Really amazing blog!!! I enjoyed the complete article? enormous written.
    construction dumpster new york

    ReplyDelete
  52. Hi Dear, have you been certainly visiting this site daily, if that's the case you then will certainly get good
    click for more info

    ReplyDelete
  53. You have touched good quality points here. In whatever way continue writing.
    containerrentalnorfolk

    ReplyDelete