September 6, 2013

Nerf Concept Compendium - Air Blasters

Nerfers typically refer to their toys as "air blasters" or (less accurately) "air guns"  if the dart is being fired by pre-compressed air. In theory, this would include anything from a small firing tank to a giant hopper slapped onto the end of an air compressor hose. Outrageous comparisons aside, air blasters are capable of longer ranges than springers, but are limited in rate of fire. On the homemade front, air blasters are not usually seen at wars due to inherent safety issues from working with compressed air. When they are used, they are highly regulated to ensure the safety of both the operator and the person at the receiving end of said operator's darts.


  1. Basic Physics of Air Blasters
  2. Pumps
  3. Firing Valves


One of the simplest air blaster models - the Nerf Air Tech 2000, or AT2K

Nearly every air blaster at its core has a handheld air pump with check valve, a firing chamber (colloquially referred to as a "tank"), and a valve to open said chamber to the barrel when the trigger is pulled. In some cases, on-board air storage is made possible either through an air tank or an expanding rubber bladder - the former can hold far more air than a similarly sized bladder, but the latter is capable of supplying more consistent pressures to the firing chamber.

When the valve on the firing chamber is opened, the compressed air within rushes through the outlet toward the atmosphere, applying force to the surfaces along its path until the air pressure reaches equilibrium. In the case of air blasters, we place a movable object (a foam dart) in the escaping air's path, and the force applied by the compressed air drives the dart down the barrel and on toward the target.

Because there is no need to build pressure upon firing, the best barrel setup for air blasters is any barrel that allows darts to easily slide through when you blow on the barrel. There should be enough friction to keep the dart from moving on its own, but no more than that. This also helps prevent air from going past the dart in the barrel and degrading the performance of your shots.

Pumps

By far the most common method of charging the chamber of an air blaster is through the use of a simple pump.
A complete pump from an AT2K, sitting above the pump tube of a Nerf Hornet
Generally speaking, pumps work by using a rubber o-ring to seal off the pump tube during the compression stroke. As the pump is pushed in, the compressed air escapes through the check valve at the rear of the pump tube - check valves are needed in order to ensure that the air is only traveling one way (into the chamber) and can't escape back through the pump tube. On the outward stroke, the o-ring moves slightly forward within its groove (it "floats"), opening an air pathway. This fills the tube with more outside air for the next compression stroke.

Some pumps will, instead of using a floating o-ring, have a second check valve at the base of the tube. This check valve will allow outside air to enter the tube on the outward stroke to relieve the vacuum that the motion would otherwise produce. These types of pumps are most often seen in Super Soakers and other water blasters; the use of liquid in the system instead of gas allows for the greatest effect - when such pumps are used for air, the compressible nature (or conversely, decompression) of the air does not immediately produce a near-vacuum pressure, causing the second check valve to activate later than desired and for a shorter duration. The end result is a less efficient pump. In general, the closer the second check valve sits to the pump tube, the better this version of pump will operate.

The overpressure valve within the pump of a Buzz Bee Big Blast (4B or BBBB)
As a safety feature, most pumps used in air blasters have overpressure valves - spring loaded check valves designed to open at a set pressure. Usually located within the pump head, these devices prevent injury to the target by prohibiting dangerously high pressures in the chamber, and also to the user by preventing pressures high enough to compromise the system. If a chamber ruptures from excess pressure, the rapid decompression can result in plastic shrapnel that could seriously injure the user of the blaster.

While these relief valves can be placed anywhere in the system, they are most effective at the pump head or near the pump's air outlet. This allows the valve to operate as soon as excess pressures form without any chance of sticking; the excess air can be vented quickly from the system before the internal system pressure equalizes.

ORPVs are a requirement for use in ANY homemade air blaster, alongside a pressure gauge for showing the maximum pressure of the blaster. One commonly used relief valve comes from McMaster-Carr, and can be adjusted for a wide range of desired pressures.

In rare cases, ORPVs are not needed do to the design of the blaster. For example, in Marshmallow Blasters, the pump head cannot travel down the pump tube completely, leaving an area of dead space. The volume of dead space in the pump determines the maximum pressure that can go into the chamber; further pumping beyond this point becomes futile, and the user is prevented from achieving absurd pressures.


Air compressors are very uncommon in the Nerf community due to expense, weight, and overall practicality. Smaller air compressors with acceptable automatic shutoff pressures are available, but still require the user to carry a power source (batteries) for operation. This extra weight is cumbersome. You will likely only see compressors used with homemade cannons designed to fire large numbers of regular darts, or rocket and arrow darts.

One exception is the Marshmallow Mazooka, which has a tiny compressor driven by 6 AA batteries. However, it is very noisy and eats through batteries at a fast rate.


There are several kinds of valves that are used to open the chamber to the dart barrel. They all have their uses.

-Pin Valves


Buzz Bee Water Warriors Ultimate Bandit, with a pin valve behind the nozzle

Pin valves are perhaps the most common type to be found in air blasters, as well as most Super Soakers up to the end of the CPS era. A disc with a rubber sealing surface (disc, o-ring, etc) seals off the air outlet of the chamber and is held in place by a weak spring (this ensures an airtight seal before you start pumping). A metal or plastic rod is attached to this piece, and runs to the outside of the chamber for connection to the trigger. O-rings are used to seal off the pin hole to prevent leakage.
Internal diagram of a pin valve
Note that it IS possible to use the pin itself to seal off the barrel - you'll just need to have o-rings sealing off both ends of the chamber, and use a larger rod to allow sufficient output. Since the air in the chamber is pressing only the outside of the pin and not against any sealing surface, the forces cancel out. Thus why this version is called the Zero Pull Valve.

This type of valve is seen in most homemade air blasters. Classic garden nozzles are pin valves that are easily available almost everywhere. PVC check valves can also be converted into pin valves when placed in reverse and given an extended pin for actuation. 3DBBQ's JSPB - The Mad Ghost effectively uses this type of valve.


Also known as backpressure valves, these are a method of controlling the air release via a floating piston within the chamber. The piston is pushed forward when the chamber is pressurized, sealing off the outlet. However, it seals against a raised surface, NOT a flat one. This allows the air to exert some force in the opposite direction. More on that later.

When the trigger is actuated, a pilot valve is opened, allowing the air within the tubing behind the piston ("pilot volume") to vent. If you vent the air quickly, then the sum of the forces acting on the piston changes - there is more area on the FRONT of the piston for exerting force than in the rear because of that raised surface. Once the piston starts moving back, the entire front of the piston is exposed to the compressed air, snapping the piston back and dumping the rest of the air down the barrel.

Nerf blasters like the Hornet and Secret Strike Pocket Blaster (SSPB) use these types of valves, but they are seen far more often in off-brand blasters like the Lanard Big Salvo and Sonic Bazooka, as well as Buzz Bee's entire Extreme Air Max line for 2013. This valve is also popular among spud cannon enthusiasts.



-Stop-Check Valves

A less common design that is often seen in Marshmallow Blasters and the like. The valve consists of a check valve with some outside mechanism that keeps it closed until the trigger is pulled. In most cases, there is a plastic catch-piece (properly known as the "seer", to borrow firearm terminology) connected to the trigger.

The Marshmallow Duel Blaster, showing both the large check valve at the outlet of the chamber and the yellow sear that holds it in place until removed via trigger pull
Several types of check valve can be used - disc, swing, etc. - as long as they can be held in place against the pressure of the air chamber.

A sprinkler valve, with the pilot volume released and the water outlet open

This type of valve is most often seen in spud cannons, where sprinkler valves have been converted to just use air pressure. When charged, a rubber diaphragm seals off the barrel. Dumping the air on the opposite side of the diaphragm causes it to quickly contract, opening the air outlet. In essence, sprinkler and piston valves operate the same way. Sprinkler valves are just built differently.


Another valve used in homemades, as well as many Super Soakers since the beginning of the Max-D product line. A ball with a port through it sit within a rubber seat, making for an airtight seal. The ball is connected to a handle or arm of some kind, allowing the user to turn the ball to open and close the valve. While reliable, ball valves are slow to fully open and normally not ideal for air blaster use.

In 2001, Larami filed for a patent for a "snap action ball valve assembly" to be used with water blasters. In what we now call the Max-D ball valve, a series of spring loaded levers are connected to the valve and the trigger. After the first lever rotates far enough, the attached spring pulls the valve arm to the open position in a faster, more fluid motion. Physically, it's the same principle used in the Air Tech pin valves - the trigger compresses a spring, which is in turn mounted on the pin, until enough force is applied to open the valve. At that point, the potential energy stored in the spring snaps the pin back for more consistent performance.
Figure 2 from the Max-D valve patent

Closed position

Once the triangular lever is nearly all the way back, the extension spring pulls the valve arm through its full motion in one swift movement.
It should be noted, though, that the external assembly can fail over time due to stress.


There are many types of valves not covered in this essay. For example, the Magstrike and Rapidfire 20 both operate using a rubber bladder for air storage and a moving piston that fires as well as advances the clip or turret. These are a variation of spool valves that are often used in paintball guns. Another paintball device, the hammer/valve assembly, is sometimes seen in less common blasters like the Light Storm series.
Diagram showing the operation of a Magstrike piston

63 comments:

  1. Very informative stuff you have got shared here. i'm glad to go to this amazing diary. Thanks for everything.

    ReplyDelete
  2. Just want to say your article is striking. The clarity in your post is simply striking and i can take for granted you are an expert on this subject. I simply stumbled upon your weblog and truly insightful information thanks a ton. best air compressor

    ReplyDelete
  3. Durable air compressor is not available everywhere. But in this site you can find information about durable air compressor. In this site all of air compressors are not only durable but also less expensive and You can also get (best air compressor reviews in this site.

    ReplyDelete
  4. This comment has been removed by the author.

    ReplyDelete
  5. I looked your post clearly. Very very thanks to you for writing a nice post. You have given nice information about air compressor. So very very thanks to you for sharing with us. Do you want any information about it? Then inter in http://www.aircompressorreviews68.com/

    ReplyDelete
  6. In fact, The article is great to know about the air blasters. It really enhance my knowledge and delight my mind. Check out more here to know about an essential component of air blaster i.e. air compressor.

    ReplyDelete
  7. You mention here how air compressor work & how to use it.Its good to know use of it.After read your contain if any one interest to buy an air compressor they can visit this site

    ReplyDelete
  8. Thank you, this helped me alot!

    ReplyDelete
  9. Let Maine set it this manner, initial choice is that the oil that's created for your precise mechanical device. Second depends upon what quantity you employ your mechanical device. If you're not victimization mechanical device for industrial or extreme service, it's best to travel with common thirty weight non-detergent oil ( modify its weight to suit the climate you're operating in).

    ReplyDelete
  10. Just a couple of years prior quarries were far away and nobody truly minded on the off chance that they made a ton of clamor and shook things up. While the security of the organization's representatives and neighbors was dependably of incredible concern, little believed was given to such things as ground vibration and air impact (commotion). Since that time, urban communities have become bigger and by and large have infringed upon or encompassed long existing mine destinations. A significant number of these operations now have close neighbors and fall inside of city breaking points.

    ReplyDelete
  11. Portable air compressor has more uses than just inflation. And, for inflation there are also different compressors, for trucks, on-board, motorcycles... www.homemachine.net

    ReplyDelete
  12. If you have an car out there that you believe merits restoring, get some pneumatic air devices and put it all on the line! Why purchase another car when you can have yours up and running in tip top condition. You will go not far off and take your car out for a twist in style as well. With a little assistance from pneumatic air tools, this is conceivable.

    ReplyDelete
  13. Pilots love their planes, and dealing with them requires various instruments. Air blaster fueled by a versatile air compressor not just give the assortment important to keep up an air ship, yet are more effective and run cooler than traditional apparatuses.

    ReplyDelete
  14. For painting your car if you go manually then it's gonna take a lot of time. So It's better to use best air compressor with supreme quality. It's fast working, place the paint perfectly and colors in a balanced way.

    ReplyDelete
  15. Compressed-air power tools can dramatically decrease the amount of time spent on a project. Many homeowners will use smaller, portable units. Air tool resource

    ReplyDelete
  16. Thanks for sharing this wonderful blog. This is well-written and insightful blog. To know about car maintenance services visit - Best Brake Rotors for automobile

    ReplyDelete
  17. Central Heating and Air Conditioning offers expert solutions, timely services and affordability to residential as well as commercial clients. ventilation

    ReplyDelete
  18. Next, what is a portable air conditioner? A portable air conditioner just like the standard air conditioner is designed specifically to cool the air inside an area but the only difference is you do not need to install the portable air conditioner to a window or to a wall. Furthermore, you can use portable air conditioners on most rooms and setting this up is fast and easy. contractors near me

    ReplyDelete
  19. Thanks for posting this info. I just want to let you know that I just check out your site and I find it very interesting and informative. air rifle reviews

    ReplyDelete
  20. No matter what tool you use from the Top hammer Here kit it will operate on standard power. The barrel will weigh about 4 - 5 pounds before the head has recently been put in. It will be approximately eight to ten inches in length.

    ReplyDelete
  21. Having installed an air conditioning system, it becomes imperative for you to think about its upkeep, a major part of which involves cleaning the home air conditioning filters, which are attached to the air conditioner. But you must be wondering why hvac repair armonk filters are installed at all and why you need to clean it regularly.

    ReplyDelete
  22. So appropriate working and support of your home's HVAC framework is an essential piece of its working. In this manner, it is dependably an incredible plan to enlist HVAC repair contractors to manage any issues that you may face. heating repair lewisboro

    ReplyDelete
  23. Hey, I’ve no doubts you’ve done some research while writing on Nerf Concept Compendium. I would expect more of this in your next write-ups, so I could get help from your information to create some content for our followers and the website.

    ReplyDelete
  24. MERV represents least proficiency announcing esteem, an esteem framework between 1-20 that estimates the air channels viability. Prijs Airco

    ReplyDelete
  25. Doing this as a daily practice in your month to month tasks and holding off on holding up until you see dust tangled reporting in real time conditioning channel will guarantee you and your family the absolute best wellbeing just as a smooth running air conditioning framework Airco

    ReplyDelete
  26. A very awesome blog post. We are really grateful for your blog post. You will find a lot of approaches after visiting your post. Airco

    ReplyDelete
  27. I think this is an informative post and it is very useful and knowledgeable. therefore, I would like to thank you for the efforts you have made in writing this article. Airco

    ReplyDelete
  28. What a really awesome post this is. Truly, one of the best posts I've ever witnessed to see in my whole life. Wow, just keep it up. Zonnepanelen

    ReplyDelete
  29. Pretty good post. I just stumbled upon your blog and wanted to say that I have really enjoyed reading your blog posts. Any way I'll be subscribing to your feed and I hope you post again soon. Big thanks for the useful info. Zonnepanelen installateur

    ReplyDelete
  30. Great article Lot's of information to Read...Great Man Keep Posting and update to People..Thanks Airconditioning

    ReplyDelete
  31. This is to guarantee your air conditioner is working at top proficiency and can broaden its life expectancy.heating repair north salem

    ReplyDelete
  32. The back yard is the most widely recognized spot to locate a focal air conditioning unit condenser unit (outside segment).Airco

    ReplyDelete
  33. The fundamental rule of Sorption Helped Air Conditioning is appeared in the realistic here.Airconditioning

    ReplyDelete
  34. But this does not mean that people should rush to stores to buy new appliances because they are having a hard time finding replacement parts for their appliances. There are still good sources of older appliance parts on the market.SubZero, Viking Refrigerator Repair in SAN MARINO

    ReplyDelete
  35. At that point, associate the fumes hose to the fumes connector. Interfacing the venting window pack connector to the window unit is the following stage. Airco installatie

    ReplyDelete
  36. This is a very articulated post. Well technical and visually excellent. You must have researched a lot. Speaks for the credibility.

    ReplyDelete
  37. Thanks for taking the time to discuss this, I feel strongly about it and love learning more on this topic. If possible, as you gain expertise, would you mind updating your blog with extra information? It is extremely helpful for me. aircon service singapore

    ReplyDelete
  38. Although most people just assume that H.V.A.C contractors are a part of the central heat and air contractors that install both furnaces for heating and air con units for cooling, air conditioning contractors have a private history that began in the 1900s when machines for building heating and cooling units began to be established. H.V.A.C contractors became a separate part of the heating and cooling industry in 1946 and were represented by their own groups exclusively concerned with H.V.A.C. ducted aircon installation sydney

    ReplyDelete
  39. Thanks for sharing such amazing post. I liked it.

    I also like to suggest you best company for aircon repair & aircon maintenance in Singapore i.e SG Airconzone. Feel free to call on +65 6684 2801 to get best deals.

    Thanks Again.

    ReplyDelete
  40. Yes, my actual blog still exists. I've finally reached a point where I can settle down somewhat, and place content when and where I want it. I was wanting to use my page both as a general info repository, as well as for things like how-to videos and other odds and ends. I just haven't had a chance to do that again until now.

    ReplyDelete
  41. Second, check the filters for cleanliness. If the filters are dirty, the air conditioner running will be uneconomical and troublesome. WTFIX Air

    ReplyDelete
  42. I like this website its a master peace ! Glad I found this on google.

    ReplyDelete
  43. I wanted to thank you for this good read!! I absolutely loved every bit of it. I have got you saved as a favorite to look at new things you post…

    ReplyDelete
  44. It’s simple, yet effective. A lot of times it’s very difficult to get that “perfect balance” between superb usability and visual appeal.
    I must say that you’ve done an excellent job with this.
    In addition, the blog loads very fast for me on Internet explorer.
    Exceptional blog.

    ReplyDelete
  45. Thank you for sharing this wonderful article, can you share basic aircon servicing article. thank you....

    ReplyDelete
  46. Truly, this article is really one of the very best in the history of articles. thank you for sharing this content. aircon servicing

    ReplyDelete
  47. thanks for sharing an wonderful info.keep sharing an wonderful content
    Aircon servicing

    ReplyDelete
  48. Aside from the recommended annual maintenance, did you know that one of the easiest ways to maintain your home air conditioning system is to regularly replace your air filter? Well most of you already knew that, but what factors do you use when replacing your filter and just as important, what factors do you use when purchasing an air filter for your home air conditioning system? ac maintenance dubai

    ReplyDelete
  49. wonderful aircon maintenance systematic article nice post thanks for sharing to all aircon service and maintenance

    ReplyDelete
  50. Hence you should know the upkeep techniques for keeping your air condition in a sound state. Airco installatie

    ReplyDelete
  51. If you ever have to travel to your vacation spot by train or plane, and it is not practical to bring along your car, araç kiralama

    ReplyDelete
  52. Numerous neighborhood air con administrations will give reasonable occasional framework registration.have a peek at this web-site

    ReplyDelete
  53. This article discusses portable hvac repair in mcallen units. After reading it, you'll have a much better idea of what to look for when you're in the market for one of these units.

    ReplyDelete
  54. Surecool is the leading Aircon maintenance and repair company in Singapore. We have been servicing the aircons of Singaporeans for over 10 years.

    aircon service Singapore, aircon servicing Singapore, best aircon servicing Singapore, Aircon service price,

    https://surecool.com.sg/

    surecoolaircon@gmail.com
    Enquire Book now 65 86538092

    #aircon service Singapore,
    #aircon servicing Singapore,
    #best aircon servicing Singapore,
    #Aircon service price,

    ReplyDelete
  55. Although most people just assume that H.V.A.C contractors are a part of the central heat and air contractors that install both furnaces for heating and air con units for cooling, air conditioning contractors have a private history that began in the 1900s when machines for building heating and cooling units began to be established. H.V.A.C contractors became a separate part of the heating and cooling industry in 1946 and were represented by their own groups exclusively concerned with H.V.A.C. split system installation

    ReplyDelete
  56. In every home equipped with central air conditioning, there comes a time when repair or replace becomes a major HVAC question. air conditioner disposal sydney

    ReplyDelete